Hydrogen Sulfide (H2S) Control for Lift Stations: Treat the Source, Then Polish the Air


If you're dealing with hydrogen sulfide at a lift station, you probably smelled it first, or found the corrosion first. By then the gas is already in the headspace and the damage has started. The better question is where the sulfide came from. Answer that, and you can pick a fix that works on the cause instead of chasing the smell.
This post covers where H2S comes from in your wet well and force main, why it eats your infrastructure, and how a two-layer approach handles both the source and the air.
Where Hydrogen Sulfide at a Lift Station Comes From
It starts with bacteria, not with the station itself. According to In-Pipe's science page, when dissolved oxygen is gone and soluble BOD is present, Desulfovibrio desulfuricans and other sulfate-reducing bacteria (SRBs) convert sulfate to sulfide. The sulfide ions pair up with hydrogen ions in the water and form hydrogen sulfide gas, which collects in the headspace of the pipe.
Lift stations make this easy. Wastewater can sit in a wet well or a force main between pump cycles, and the oxygen runs out. Force mains are the worst case. In-Pipe's page describes them as "completely anaerobic, typically with a thriving community of Sulfate-Reducing Bacteria." If your station pushes flow through a long force main, the sulfide is probably being made well before the water reaches the discharge manhole.

Why H2S Corrosion Is the Bigger Bill
The gas doesn't just smell. Bacteria living on the inside surface of the headspace pipe oxidize it to sulfuric acid. Per In-Pipe's page, that acid "is highly corrosive to many common piping materials, including steel, ductile iron and concrete," and it keeps forming as long as the gas is there. The same page cites a 1991 EPA line worth keeping on your desk: controlling H2S corrosion in existing systems "is the preferred alternative to premature replacement of system components."
That's the number that never shows up on a complaint log. It shows up in the capital budget a few years later. We break down the damage in more detail in H2S corrosion is quietly destroying your lift stations.
One safety note, and this is general industry practice, not an In-Pipe claim: don't use your nose as a gauge. At higher concentrations H2S can dull your sense of smell. Use a gas monitor and follow your confined-space procedures every time.
Layer One: Cut the Sulfide at the Source
In-Pipe goes after the sulfate reducers in the biofilm upstream of the station. Bacillus are dosed continuously into the collection system, where they compete with the SRBs for food and space. In-Pipe calls this competitive exclusion. The science says the shift lets the biofilm repopulate with bacteria that are "more flexible to convert organic matter," which "prevents the proliferation of SRBs."
Here's what In-Pipe reports. In a study led by Dr. Eberhard Morgenroth of the University of Illinois, a shift in the dominant microbial populations cut dissolved sulfides 50% after 20 days of continuous addition, from 0.45 mg/l to 0.23 mg/l. The same page also reports that hydrogen sulfide production dropped about 65 to 100% once Bacillus established themselves in the microbial community. Those numbers come from In-Pipe's own science page, not from an independent review, and your system will behave differently. Treat them as a reason to run a trial, not a guarantee.
Timing matters too. In-Pipe's page puts the first changes at 30 to 60 days. It also says competitive exclusion is slower in force mains than in gravity sewers, so a force main needs a more aggressive dosing plan. If you're staring at a summer odor spike, this layer won't fix it next week. For the odor side of the same approach, see our look at sewer odor control solutions.
Layer Two: Polish the Air at the Vent
Biological treatment upstream cuts the sulfide in the water. Some gas will still reach the wet well, and that's where In-Pipe's IPT-AOP-16 comes in. The page says it "connects to the existing lift station vent to oxidize hydrogen sulfide outside of the lift station environment in order to scrub odors before emission to ambient air and to prevent corrosion of the existing infrastructure."
What In-Pipe reports about the unit:
It uses no chemicals and needs only 120V power.
It typically takes "less than 25% of the footprint of biological scrubber devices and with 50% of the power requirements."
The photocatalytic cells make hydroxyl radical oxidizers from UV light, and each cell lasts 2 to 3 years. Lamp replacement takes less than an hour.
Units can be installed in parallel if you need to scale up.
In-Pipe positions it as the finishing step: after collection system bioaugmentation removes "the majority of the H2S," the unit is "an easy and efficient way to polish the air in the lift station headspace." One honest limit: In-Pipe's page doesn't publish a removal percentage or ppm target for the unit. Ask for site-specific performance data before you commit.
How to Match the Layers to Your Station
Start with a baseline. Measure dissolved sulfide at the wet well before you change anything, so you can tell what moved. In-Pipe's own field comparisons use a Hach total sulfide test kit, which is a reasonable place to start.
Then match the fix to the problem. A station fed by a long force main is making sulfide upstream of your vent, so layer one is where the cause lives. A station that's meeting its sulfide numbers but still sending odor to the neighbors may need layer two on the vent. Many stations will want both. In-Pipe isn't claiming this replaces your gas monitoring or your confined-space program, and it doesn't repair concrete that's already damaged.
If you've got a station that keeps landing on the complaint list, talk with In-Pipe about a lift station odor control plan built around your force main length, your flow, and what you're dosing today.





Comments